IB-1 Sound Isolation Clip
Discounts shown in cart.
Availability: IN STOCK
IB-1 Sound Isolation Clips - A favorite for Developers, Contractors, Architects, and anyone who needs effective economical decoupling for impact and airborne noise.
The IB-1 Sound Isolation Clip is an high-performing decoupling value clip. IB-1 limits the connection points between the drywall and walls and ceilings framing
Drywall can be installed either horizontally or vertically on soundproofing clips.
Resilient IB-1 Sound Isolation Clips perform two main functions. First, because they are spaced in rows 24" apart (generally), the drywall is attached with far fewer contact areas. Second, clips and hat track are resilient. They allow the wall to flex, and this increases sound isolation as well as lowering the troublesome primary low-frequency resonance point.
This IB-1 Soundproofing Clip performs similarly to other clips, but the low cost leaves more room to invest in extra mass (drywall) and damping (Green Glue). The resulting system is far superior to using clips and drywall alone.
The IB-1 Clip can be used with wood or steel wall studs. These clips are particularly useful on open ceilings where there are neighbors overhead. Significant relief from neighbor noise can be obtained when we first start with clips to decouple the ceiling drywall.
NOTE: Use with 25 gauge 7/8" Drywall Furring Channel Only
STC Source Side Studs Insulation Receive Side 71 Two layers of 5/8" Gypsum + Green Glue (58OZ per 4x8 sheet) Wood 24" OC R13 IB-1 Soundproofing Clip 24" O.C. + 7/8" Drywall Furring Channel + Two layers of 5/8" Gypsum (Type X) + Green Glue (58OZ per 4x8 sheet) 67 Single layer of 5/8" Gypsum Board (Type X) Wood 24" OC R13 IB-1 Soundproofing Clip 24" O.C. + 7/8" Drywall Furring Channel + Two layers of 5/8" Gypsum (Type X)+ Green Glue (58OZ per 4x8 sheet) 60 Two layers of 5/8" Gypsum Board (Type X) Wood 24" OC R13 IB-1 Soundproofing Clip 24" O.C. + 7/8" Drywall Furring Channel + Two layers of 5/8" Gypsum (Type X) 58 Single layer of 5/8" Gypsum Board (Type X) Wood 24" OC R13 IB-1 Soundproofing Clip 24" O.C. + 7/8" Drywall Furring Channel + Two layers of 5/8" Gypsum (Type X) 53 Single layer of 5/8" Gypsum Board (Type X) Wood 24" OC R13 IB-1 Soundproofing Clip 24" O.C. + 7/8" Drywall Furring Channel + Single layer 5/8" Gypsum (Type X)
Adding IB-1 Clips improve sound isolation by decoupling drywall from your room framing. Install Soundproofing Clips directly to ceiling or wall framing using standard screws . Snap 7/8″ Drywall Furring Channel into Soundproofing Clip to decrease the conduction contact area and increase the flexibility. Fasten standard drywall following local building codes. The combination of increased resilience and the mass from the drywall create a powerful ally against noise. See the official lab results below.
- Economical compared to expensive 2-Part Clips
- Similar Performance to 2-Part Clips
- Fast Installation, single screw attachment
- UL Rating for commercial installation
- Galvanized finish
Snap Drywall Furring Channel into the IB-1 Clip.
- Length: 3 1/4″
- Height: 3/4″
- Width: 1 5/16″
- Vertical Spacing: 24″
- Horizontal Spacing: 48″
- Design Load: 36 lbs per clip
Clip to Wood Framing: 1.25 inch screw length, #6 min. shank (coarse thread), bugle, or hex-head screws of equal or greater size. Minimum pullout shear: 108 lbs through the clip to wood framing member.
Clip to Steel Framing: Install 1 inch screws (25mm) minimum length; #8 minimum shank; Type S (fine thread); bugle, or hex head screws to equal or greater size. Min. pullout shear: 108 lbs. through the clip to steel framing member.
Drywall to Furring Channel: Use the appropriate length fine-thread drywall screws designed for use with 25 gauge steel framing. Install per local Building Code.
Soundproofing Clips approved Mechanical Fasteners
Shipping & Liability Statement
$100 Minimum Order for FREE SHIPPING
Additional $25 Shipping Charge for orders less than $100.
Warehouse Fee of +$10 per order.
60 Days on all Returns All returned unused items are subject to warehouse and 20% re-stock fees. No Returns on Open/Partial Cases, Pails, Single Tubes, Outlet Putty Pads
The Soundproofing Company presents these products and construction concepts with the understanding that local Building Codes vary. It is the responsibility of the installer to ensure product is properly installed, and that these concepts meet local Building Code. The Soundproofing Company is not liable for mis-installation or non-compliance with local code.
Soundproofing Company, Inc.
527 W. Morley Dr. Saginaw, MI. 48601
Support: (800) 397-8791
Noisy floors are a significant and growing issue as more people are opting for hard surface flooring. This creates distinct soundproofing challenges. We offer solutions tailored to your commercial or residential needs.